[Federal Register Volume 84, Number 221 (Friday, November 15, 2019)]
[Proposed Rules]
[Pages 62485-62488]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-24532]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2019-0865; Product Identifier 2019-NM-158-AD]
RIN 2120-AA64
Airworthiness Directives; Airbus SAS Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for all Airbus SAS Model A350-941 and -1041 airplanes. This proposed AD
was prompted by reports of passenger door girt bar fitting assembly
safety hooks being stuck in the upward position. This proposed AD would
require repetitive detailed inspections of girt bar fitting assemblies,
repetitive greasing of girt bar fitting assembly bushes, and, depending
[[Page 62486]]
on findings, accomplishment of applicable corrective actions, as
specified in a European Union Aviation Safety Agency (EASA) AD, which
will be incorporated by reference. The FAA is proposing this AD to
address the unsafe condition on these products.
DATES: The FAA must receive comments on this proposed AD by December
30, 2019.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For the material identified in this proposed AD that will be
incorporated by reference (IBR), contact the EASA, Konrad-Adenauer-Ufer
3, 50668 Cologne, Germany; telephone +49 221 89990 1000; email
[email protected]; internet www.easa.europa.eu. You may find this IBR
material on the EASA website at https://ad.easa.europa.eu. You may view
this IBR material at the FAA, Transport Standards Branch, 2200 South
216th St., Des Moines, WA. For information on the availability of this
material at the FAA, call 206-231-3195. It is also available in the AD
docket on the internet at https://www.regulations.gov by searching for
and locating Docket No. FAA-2019-0865.
Examining the AD Docket
You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2019-
0865; or in person at Docket Operations between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays. The AD docket contains
this NPRM, the regulatory evaluation, any comments received, and other
information. The street address for Docket Operations is listed above.
Comments will be available in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Kathleen Arrigotti, Aerospace
Engineer, International Section, Transport Standards Branch, FAA, 2200
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3218.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under the ADDRESSES section. Include ``Docket No. FAA-2019-0865;
Product Identifier 2019-NM-158-AD'' at the beginning of your comments.
The FAA specifically invites comments on the overall regulatory,
economic, environmental, and energy aspects of this NPRM. The FAA will
consider all comments received by the closing date and may amend this
NPRM based on those comments.
The FAA will post all comments received, without change, to https://www.regulations.gov, including any personal information you provide.
The FAA will also post a report summarizing each substantive verbal
contact received about this NPRM.
Discussion
The EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2019-0207, dated August 22, 2019
(``EASA AD 2019-0207'') (also referred to as the Mandatory Continuing
Airworthiness Information, or ``the MCAI''), to correct an unsafe
condition for all Airbus SAS Model A350-941 and -1041 airplanes.
This proposed AD was prompted by reports of passenger door girt bar
fitting assembly safety hooks being stuck in the upward position. The
FAA is proposing this AD to address this condition, which could lead to
girt bar disengagement from the girt bar fitting assembly and
consequent failure of the passenger door slide deployment during an
emergency, possibly preventing safe evacuation of the airplane. See the
MCAI for additional background information.
Related IBR Material Under 1 CFR Part 51
EASA AD 2019-0207 describes procedures for repetitive detailed
inspections of girt bar fitting assemblies, repetitive greasing of girt
bar fitting assembly bushes, and, depending on findings, accomplishment
of applicable corrective actions. Corrective actions include rework and
replacement. EASA AD 2019-0207 also describes procedures for sending
inspection results to Airbus. This material is reasonably available
because the interested parties have access to it through their normal
course of business or by the means identified in the ADDRESSES section.
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to a bilateral agreement with the State of Design Authority, the FAA
has been notified of the unsafe condition described in the MCAI
referenced above. The FAA is proposing this AD because the agency
evaluated all the relevant information and determined the unsafe
condition described previously is likely to exist or develop in other
products of the same type design.
Proposed AD Requirements
This proposed AD would require accomplishing the actions specified
in EASA AD 2019-0207 described previously, as incorporated by
reference, except for any differences identified as exceptions in the
regulatory text of this AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA initially worked with Airbus and EASA to develop a
process to use certain EASA ADs as the primary source of information
for compliance with requirements for corresponding FAA ADs. The FAA has
since coordinated with other manufacturers and civil aviation
authorities (CAAs) to use this process. As a result, EASA AD 2019-0207
will be incorporated by reference in the FAA final rule. This proposed
AD would, therefore, require compliance with EASA AD 2019-0207 in its
entirety, through that incorporation, except for any differences
identified as exceptions in the regulatory text of this proposed AD.
Using common terms that are the same as the heading of a particular
section in the EASA AD does not mean that operators need comply only
with that section. For example, where the AD requirement refers to
``all required actions and compliance times,'' compliance with this AD
requirement is not limited to the section titled ``Required Action(s)
and Compliance Time(s)'' in the EASA AD. Service information specified
in EASA AD 2019-0207 that is required for compliance with EASA AD 2019-
0207 will be available on the internet at https://www.regulations.gov
by searching for and locating Docket No. FAA-2019-0865 after the FAA
final rule is published.
[[Page 62487]]
Interim Action
The FAA considers this proposed AD interim action. If final action
is later identified, the FAA might consider further rulemaking then.
Costs of Compliance
The FAA estimates that this proposed AD affects 13 airplanes of
U.S. registry. The FAA estimates the following costs to comply with
this proposed AD:
Estimated Costs for Required Actions *
----------------------------------------------------------------------------------------------------------------
Cost per Cost on U.S.
Labor cost Parts cost product operators
----------------------------------------------------------------------------------------------------------------
1 work-hour x $85 per hour = $85............................. $0 $85 $1,105
----------------------------------------------------------------------------------------------------------------
* Table does not include estimated costs for reporting.
The FAA estimates that it would take about 1 work-hour per product
to comply with the proposed reporting requirement in this proposed AD.
The average labor rate is $85 per hour. Based on these figures, the FAA
estimates the cost of reporting the inspection results on U.S.
operators to be $1,105, or $85 per product.
The FAA estimates the following costs to do any necessary on-
condition actions that would be required based on the results of any
required actions. The FAA has no way of determining the number of
aircraft that might need these on-condition actions:
Estimated Costs of On-Condition Actions
------------------------------------------------------------------------
Labor cost Parts cost Cost per product
------------------------------------------------------------------------
Up to 3 work-hours x $85 per * *$255
hour = $255....................
------------------------------------------------------------------------
* The FAA has received no definitive data that would enable the agency
to provide parts cost estimates for the on-condition actions specified
in this proposed AD.
Paperwork Reduction Act
A federal agency may not conduct or sponsor, and a person is not
required to respond to, nor shall a person be subject to penalty for
failure to comply with a collection of information subject to the
requirements of the Paperwork Reduction Act unless that collection of
information displays a current valid OMB control number. The control
number for the collection of information required by this NPRM is 2120-
0056. The paperwork cost associated with this NPRM has been detailed in
the Costs of Compliance section of this document and includes time for
reviewing instructions, as well as completing and reviewing the
collection of information. Therefore, all reporting associated with
this NPRM is mandatory. Send comments regarding this burden estimate or
any other aspect of this collection of information, including
suggestions for reducing this burden to: Information Collection
Clearance Officer, Federal Aviation Administration, 10101 Hillwood
Parkway, Fort Worth, TX 76177-1524.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
This proposed AD is issued in accordance with authority delegated
by the Executive Director, Aircraft Certification Service, as
authorized by FAA Order 8000.51C. In accordance with that order,
issuance of ADs is normally a function of the Compliance and
Airworthiness Division, but during this transition period, the
Executive Director has delegated the authority to issue ADs applicable
to transport category airplanes and associated appliances to the
Director of the System Oversight Division.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
Airbus SAS: Docket No. FAA-2019-0865; Product Identifier 2019-NM-
158-AD.
[[Page 62488]]
(a) Comments Due Date
The FAA must receive comments by December 30, 2019.
(b) Affected ADs
None.
(c) Applicability
This AD applies to all Airbus SAS Model A350-941 and -1041
airplanes, certificated in any category.
(d) Subject
Air Transport Association (ATA) of America Code 52, Doors.
(e) Reason
This AD was prompted by reports of passenger door girt bar
fitting assembly safety hooks being stuck in the upward position. We
are issuing this AD to address this condition, which could lead to
girt bar disengagement from the girt bar fitting assembly and
consequent failure of the passenger door slide deployment during an
emergency, possibly preventing safe evacuation of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, European Union Aviation Safety Agency (EASA) AD
2019-0207, dated August 22, 2019 (``EASA AD 2019-0207'').
(h) Exceptions to EASA AD 2019-0207
(1) Where EASA AD 2019-0207 refers to its effective date, this
AD requires using the effective date of this AD.
(2) The ``Remarks'' section of EASA AD 2019-0207 does not apply
to this AD.
(3) Paragraph (4) of EASA AD 2019-0207 specifies to report
inspection results to Airbus within a certain compliance time. For
this AD, report inspection results at the applicable time specified
in paragraph (h)(3)(i) or (ii) of this AD.
(i) If the inspection was done on or after the effective date of
this AD: Submit the report within 90 days after the inspection.
(ii) If the inspection was done before the effective date of
this AD: Submit the report within 90 days after the effective date
of this AD.
(i) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Section, Transport Standards Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the International Section, send it to the attention of
the person identified in paragraph (j)(2) of this AD. Information
may be emailed to: [email protected]. Before using any
approved AMOC, notify your appropriate principal inspector, or
lacking a principal inspector, the manager of the local flight
standards district office/certificate holding district office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, International
Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's
EASA Design Organization Approval (DOA). If approved by the DOA, the
approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): For any service information
referenced in EASA AD 2019-0207 that contains RC procedures and
tests: Except as required by paragraph (i)(2) of this AD, RC
procedures and tests must be done to comply with this AD; any
procedures or tests that are not identified as RC are recommended.
Those procedures and tests that are not identified as RC may be
deviated from using accepted methods in accordance with the
operator's maintenance or inspection program without obtaining
approval of an AMOC, provided the procedures and tests identified as
RC can be done and the airplane can be put back in an airworthy
condition. Any substitutions or changes to procedures or tests
identified as RC require approval of an AMOC.
(4) Paperwork Reduction Act Burden Statement: A federal agency
may not conduct or sponsor, and a person is not required to respond
to, nor shall a person be subject to a penalty for failure to comply
with a collection of information subject to the requirements of the
Paperwork Reduction Act unless that collection of information
displays a current valid OMB Control Number. The OMB Control Number
for this information collection is 2120-0056. Public reporting for
this collection of information is estimated to be approximately 1
hour per response, including the time for reviewing instructions,
completing and reviewing the collection of information. All
responses to this collection of information are mandatory. Send
comments regarding this burden estimate or any other aspect of this
collection of information, including suggestions for reducing this
burden to: Information Collection Clearance Officer, Federal
Aviation Administration, 10101 Hillwood Parkway, Fort Worth, TX
76177-1524.
(j) Related Information
(1) For information about EASA AD 2019-0207, contact the EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221
89990 6017; email [email protected]; Internet www.easa.europa.eu.
You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA, Transport
Standards Branch, 2200 South 216th St., Des Moines, WA. For
information on the availability of this material at the FAA, call
206-231-3195. This material may be found in the AD docket on the
internet at https://www.regulations.gov by searching for and
locating Docket No. FAA-2019-0865.
(2) For more information about this AD, contact Kathleen
Arrigotti, Aerospace Engineer, International Section, Transport
Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198;
telephone and fax 206-231-3218.
Issued in Des Moines, Washington, on November 1, 2019.
Dionne Palermo,
Acting Director, System Oversight Division, Aircraft Certification
Service.
[FR Doc. 2019-24532 Filed 11-14-19; 8:45 am]
BILLING CODE 4910-13-P