[Federal Register Volume 85, Number 149 (Monday, August 3, 2020)]
[Proposed Rules]
[Pages 46563-46566]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-16628]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2020-0678; Product Identifier 2020-NM-098-AD]
RIN 2120-AA64
Airworthiness Directives; Dassault Aviation Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to supersede Airworthiness Directive (AD)
2019-24-11, which applies to certain Dassault Aviation Model FALCON
900EX airplanes. AD 2019-24-11 requires revising the existing
maintenance or inspection program, as applicable, to incorporate new or
more restrictive airworthiness limitations. Since the FAA issued AD
2019-24-11, the FAA determined that new or more restrictive
airworthiness limitations are necessary. This proposed AD would
continue to require those maintenance or inspection program revisions,
and would also require revising the existing maintenance or inspection
program, as applicable, to incorporate additional new or more
restrictive airworthiness limitations, as specified in a European Union
Aviation Safety Agency (EASA) AD, which will be incorporated by
reference. The FAA is proposing this AD to address the unsafe condition
on these products.
DATES: The FAA must receive comments on this proposed AD by September
17, 2020.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590, between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays.
For EASA material identified in this proposed AD that will be
incorporated by reference (IBR), contact the EASA, Konrad-Adenauer-Ufer
3, 50668 Cologne, Germany; telephone +49 221 8999 000; email
[email protected]; internet www.easa.europa.eu. You may find this IBR
material on the EASA website at https://ad.easa.europa.eu.
For Dassault service information identified in the proposed AD,
contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box
2000, South Hackensack, NJ 07606; telephone 201-440-6700; internet
https://www.dassaultfalcon.com.
You may view this IBR material at the FAA, Airworthiness Products
Section, Operational Safety Branch, 2200 South 216th St., Des Moines,
WA. For information on the availability of this material at the FAA,
call 206-231-3195. It is also available in the AD docket on the
internet at https://www.regulations.gov by searching for and locating
Docket No. FAA-2020-0678.
Examining the AD Docket
You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0678; or in person at Docket Operations between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays. The AD docket contains
this NPRM, any comments received, and other information. The street
address for
[[Page 46564]]
Docket Operations is listed above. Comments will be available in the AD
docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer,
Large Aircraft Section, International Validation Branch, FAA, 2200
South 216th St., Des Moines, WA 98198; telephone and fax: 206-231-3226;
email: [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. The most helpful comments reference a
specific portion of the proposal, explain the reason for any
recommended change, and include supporting data. To ensure the docket
does not contain duplicate comments, commenters should send only one
copy of written comments, or if comments are filed electronically,
commenters should submit only one time. Send your comments to an
address listed under the ADDRESSES section. Include ``Docket No. FAA-
2020-0678; Product Identifier 2020-NM-098-AD'' at the beginning of your
comments.
Except for Confidential Business Information (CBI) as described in
the following paragraph, and other information as described in 14 CFR
11.35, the FAA will post all comments received, without change, as well
as a report summarizing each substantive public contact with FAA
personnel concerning this proposed rulemaking. Before acting on this
proposal, the FAA will consider all comments received by the closing
date for comments. The FAA will consider comments filed after the
comment period has closed if it is possible to do so without incurring
expense or delay. The FAA may change this NPRM because of those
comments.
Confidential Business Information
CBI is commercial or financial information that is both customarily
and actually treated as private by its owner. Under the Freedom of
Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public
disclosure. If your comments responsive to this NPRM contain commercial
or financial information that is customarily treated as private, that
you actually treat as private, and that is relevant or responsive to
this NPRM, it is important that you clearly designate the submitted
comments as CBI. Please mark each page of your submission containing
CBI as ``PROPIN.'' The FAA will treat such marked submissions as
confidential under the FOIA, and they will not be placed in the public
docket of this NPRM. Submissions containing CBI should be sent to the
person identified in the FOR FURTHER INFORMATION CONTACT section. Any
commentary that the FAA receives which is not specifically designated
as CBI will be placed in the public docket for this rulemaking.
Discussion
The FAA issued AD 2019-24-11, Amendment 39-19814 (84 FR 69997,
December 20, 2019) (``AD 2019-24-11''), which applies to certain
Dassault Aviation Model FALCON 900EX airplanes. AD 2019-24-11 requires
revising the existing maintenance or inspection program, as applicable,
to incorporate new or more restrictive airworthiness limitations. The
FAA issued AD 2019-24-11 to address reduced structural integrity of the
airplane.
AD 2019-24-11 specifies that accomplishing the actions required by
paragraph (g) or (i) of that AD terminates the requirements of
paragraph (g)(1) of AD 2010-26-05, Amendment 39-16544 (75 FR 79952,
December 21, 2010) for Dassault Aviation Model FALCON 900EX airplanes,
serial numbers 1 through 96 inclusive, and serial numbers 98 through
119 inclusive.
Actions Since AD 2019-24-11 Was Issued
Since the FAA issued AD 2019-24-11, the FAA determined that new or
more restrictive airworthiness limitations are necessary.
The EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2020-0116, dated May 20, 2020
(``EASA AD 2020-0116'') (also referred to as the Mandatory Continuing
Airworthiness Information, or ``the MCAI''), to correct an unsafe
condition for certain Dassault Aviation Model FALCON 900EX airplanes.
EASA AD 2020-0116 superseded EASA AD 2019-0133 (which corresponds to
FAA AD 2019-24-11).
This proposed AD was prompted by a determination that new or more
restrictive airworthiness limitations are necessary. The FAA is
proposing this AD to address reduced structural integrity of the
airplane. See the MCAI for additional background information.
Related IBR Material Under 1 CFR Part 51
EASA AD 2020-0116 describes new or more restrictive maintenance
tasks and airworthiness limitations.
This proposed AD would also require Chapter 5-40, Airworthiness
Limitations, Revision 16, dated September 2018, of the Dassault FALCON
900EX Maintenance Manual, which the Director of the Federal Register
approved for incorporation by reference as of January 24, 2020 (84 FR
69997, December 20, 2019).
This material is reasonably available because the interested
parties have access to it through their normal course of business or by
the means identified in the ADDRESSES section.
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to the FAA's bilateral agreement with the State of Design Authority,
the FAA has been notified of the unsafe condition described in the MCAI
and service information referenced above. The FAA is proposing this AD
because the FAA evaluated all pertinent information and determined an
unsafe condition exists and is likely to exist or develop on other
products of the same type design.
Proposed AD Requirements
This proposed AD would retain the requirements of AD 2019-24-11.
This proposed AD would also require revising the existing maintenance
or inspection program, as applicable, to incorporate new or more
restrictive airworthiness limitations, which are specified in EASA AD
2020-0116 described previously, as incorporated by reference. Any
differences with EASA AD 2020-0116 are identified as exceptions in the
regulatory text of this AD.
This proposed AD would require revisions to certain operator
maintenance documents to include new actions (e.g., inspections).
Compliance with these actions is required by 14 CFR 91.403(c). For
airplanes that have been previously modified, altered, or repaired in
the areas addressed by this proposed AD, the operator may not be able
to accomplish the actions described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must request
approval for an alternative method of compliance according to paragraph
(m)(1) of this proposed AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA initially worked with Airbus and EASA to develop a
process to use certain EASA ADs as the primary source of information
for compliance with requirements for corresponding
[[Page 46565]]
FAA ADs. The FAA has since coordinated with other manufacturers and
civil aviation authorities (CAAs) to use this process. As a result,
EASA AD 2020-0116 will be incorporated by reference in the FAA final
rule. This proposed AD would, therefore, require compliance with EASA
AD 2020-0116 in its entirety, through that incorporation, except for
any differences identified as exceptions in the regulatory text of this
proposed AD. Using common terms that are the same as the heading of a
particular section in the EASA AD does not mean that operators need
comply only with that section. For example, where the AD requirement
refers to ``all required actions and compliance times,'' compliance
with this AD requirement is not limited to the section titled
``Required Action(s) and Compliance Time(s)'' in the EASA AD.
Service information specified in EASA AD 2020-0116 that is required
for compliance with EASA AD 2020-0116 will be available on the internet
at https://www.regulations.gov by searching for and locating Docket No.
FAA-2020-0678 after the FAA final rule is published.
Airworthiness Limitation ADs Using the New Process
The FAA's process of incorporating by reference MCAI ADs as the
primary source of information for compliance with corresponding FAA ADs
has been limited to certain MCAI ADs (primarily those with service
bulletins as the primary source of information for accomplishing the
actions required by the FAA AD). However, the FAA is now expanding the
process to include MCAI ADs that require a change to airworthiness
limitation documents, such as airworthiness limitation sections.
For these ADs that incorporate by reference an MCAI AD that changes
airworthiness limitations, the FAA requirements are unchanged.
Operators must revise the existing maintenance or inspection program,
as applicable, to incorporate the information specified in the new
airworthiness limitation document. The airworthiness limitations must
be followed according to 14 CFR 91.403(c) and 91.409(e).
Costs of Compliance
The FAA estimates that this proposed AD affects 72 airplanes of
U.S. registry. The FAA estimates the following costs to comply with
this proposed AD:
The FAA estimates the total cost per operator for the retained
actions from AD 2019-24-11 to be $7,650 (90 work-hours x $85 per work-
hour).
The FAA has determined that revising the maintenance or inspection
program takes an average of 90 work-hours per operator, although the
FAA recognizes that this number may vary from operator to operator. In
the past, the FAA has estimated that this action takes 1 work-hour per
airplane. Since operators incorporate maintenance or inspection program
changes for their affected fleet(s), the FAA has determined that a per-
operator estimate is more accurate than a per-airplane estimate.
Therefore, the FAA estimates the total cost per operator for the new
proposed actions to be $7,650 (90 work-hours x $85 per work-hour).
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: General requirements.
Under that section, Congress charges the FAA with promoting safe flight
of civil aircraft in air commerce by prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety in air commerce. This regulation is within the scope of that
authority because it addresses an unsafe condition that is likely to
exist or develop on products identified in this rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing Airworthiness Directive (AD)
2019-24-11, Amendment 39-19814 (84 FR 69997, December 20, 2019), and
adding the following new AD:
Dassault Aviation: Docket No. FAA-2020-0678; Product Identifier
2020-NM-098-AD.
(a) Comments Due Date
The FAA must receive comments by September 17, 2020.
(b) Affected ADs
(1) This AD replaces AD 2019-24-11, Amendment 39-19814 (84 FR
69997, December 20, 2019) (``AD 2019-24-11'').
(2) This AD affects AD 2010-26-05, Amendment 39-16544 (75 FR
79952, December 21, 2010) (``AD 2010-26-05'').
(c) Applicability
This AD applies to Dassault Aviation Model FALCON 900EX
airplanes, certificated in any category, as identified in European
Union Aviation Safety Agency (EASA) AD 2020-0116, dated May 20, 2020
(``EASA AD 2020-0116'').
(d) Subject
Air Transport Association (ATA) of America Code 05, Time Limits/
Maintenance Checks.
(e) Reason
This AD was prompted by a determination that new or more
restrictive airworthiness limitations are necessary. The FAA is
issuing this AD to address reduced structural integrity of the
airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Retained Maintenance or Inspection Program Revision, With No
Changes
This paragraph restates the requirements of paragraph (i) of AD
2019-24-11, with no changes. Within 90 days after January 24, 2020
(the effective date AD 2019-24-11), revise the existing maintenance
or inspection program, as applicable, to incorporate the information
specified in Chapter 5-40,
[[Page 46566]]
Airworthiness Limitations, Revision 16, dated September 2018, of the
Dassault FALCON 900EX Maintenance Manual. The initial compliance
times for accomplishing the actions are at the times specified in
Chapter 5-40, Airworthiness Limitations, Revision 16, dated
September 2018, or 90 days after the January 24, 2020, whichever
occurs later, except as provided by paragraphs (g)(1) through (4) of
this AD. Accomplishing the maintenance or inspection program
revision required by paragraph (i) of this AD terminates the
requirements of this paragraph.
(1) The term ``LDG'' in the ``First Inspection'' column of any
table in the service information means total airplane landings.
(2) The term ``FH'' in the ``First Inspection'' column of any
table in the service information means total flight hours.
(3) The term ``FC'' in the ``First Inspection'' column of any
table in the service information means total flight cycles.
(4) The term ``M'' in the ``First Inspection'' column of any
table in the service information means months since the date of
issuance of the original airworthiness certificate or the date of
issuance of the original export certificate of airworthiness.
(h) Retained Restrictions on Alternative Actions and Intervals, With a
New Exception
This paragraph restates the requirements of paragraph (j) of AD
2019-24-11, with a new exception. Except as required by paragraph
(i) of this AD, after the maintenance or inspection program has been
revised as required by paragraph (g) of this AD, no alternative
actions (e.g., inspections) or intervals may be used unless the
actions or intervals are approved as an alternative method of
compliance (AMOC) in accordance with the procedures specified in
paragraph (m)(1) of this AD.
(i) New Maintenance or Inspection Program Revision
Except as specified in paragraph (j) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, EASA AD 2020-0116. Accomplishing the maintenance or
inspection program revision required by this paragraph terminates
the requirements of paragraph (g) of this AD.
(j) Exceptions to EASA AD 2020-0116
(1) The requirements specified in paragraphs (1) and (2) of EASA
AD 2020-0116 do not apply to this AD.
(2) Paragraph (3) of EASA AD 2020-0116 specifies revising ``the
approved AMP'' within 12 months after its effective date, but this
AD requires revising the existing maintenance or inspection program,
as applicable, to incorporate the ``limitations, tasks and
associated thresholds and intervals'' specified in paragraph (3) of
EASA AD 2020-0116 within 90 days after the effective date of this
AD.
(3) The initial compliance time for doing the tasks specified in
paragraph (3) of EASA AD 2020-0116 is at the applicable ``associated
thresholds'' specified in paragraph (3) of EASA AD 2020-0116, or
within 90 days after the effective date of this AD, whichever occurs
later.
(4) The provisions specified in paragraphs (4) and (5) of EASA
AD 2020-0116 do not apply to this AD.
(5) The ``Remarks'' section of EASA AD 2020-0116 does not apply
to this AD.
(k) New Provisions for Alternative Actions and Intervals
After the maintenance or inspection program has been revised as
required by paragraph (i) of this AD, no alternative actions (e.g.,
inspections) and intervals are allowed unless they are approved as
specified in the provisions of the ``Ref. Publications'' section of
EASA AD 2020-0116.
(l) Terminating Actions for Certain Actions in AD 2010-26-05
Accomplishing the actions required by paragraph (g) or (i) of
this AD terminates the requirements of paragraph (g)(1) of AD 2010-
26-05, for Dassault Aviation Model FALCON 900EX airplanes, serial
numbers 1 through 96 inclusive, and serial numbers 98 through 119
inclusive.
(m) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
Large Aircraft Section, International Validation Branch, FAA, has
the authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the Large Aircraft Section, International Validation
Branch, send it to the attention of the person identified in
paragraph (n)(2) of this AD. Information may be emailed to: [email protected].
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions from a manufacturer, the instructions must be
accomplished using a method approved by the Manager, Large Aircraft
Section, International Validation Branch, FAA; or EASA; or Dassault
Aviation's EASA Design Organization Approval (DOA). If approved by
the DOA, the approval must include the DOA-authorized signature.
(n) Related Information
(1) For information about EASA AD 2020-0116, contact the EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221
8999 000; email [email protected]; internet www.easa.europa.eu. You
may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA,
Airworthiness Products Section, Operational Safety Branch, 2200
South 216th St., Des Moines, WA. For information on the availability
of this material at the FAA, call 206-231-3195. This material may be
found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2020-0678.
(2) For more information about this AD, contact Tom Rodriguez,
Aerospace Engineer, Large Aircraft Section, International Validation
Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone
and fax 206-231-3226; email [email protected].
Issued on July 27, 2020.
Gaetano A. Sciortino,
Deputy Director for Strategic Initiatives, Compliance & Airworthiness
Division, Aircraft Certification Service.
[FR Doc. 2020-16628 Filed 7-31-20; 8:45 am]
BILLING CODE 4910-13-P