[Federal Register Volume 85, Number 100 (Friday, May 22, 2020)]
[Proposed Rules]
[Pages 31083-31085]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2020-10978]
[[Page 31083]]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2020-0456; Product Identifier 2020-NM-053-AD]
RIN 2120-AA64
Airworthiness Directives; Airbus SAS Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for certain Airbus SAS Model A330-202, -203, -223, -243, -301, -321, -
322, -323, -341, -342, and -343 airplanes; and Model A340-200 and -300
series airplanes. This proposed AD was prompted by a report indicating
that the allowable load limits on the vertical tail plane could be
reached and possibly exceeded in cases of multiple rudder doublet
inputs. This proposed AD would require upgrading the flight control
data concentrator (FCDC), associated flight control primary computer
(FCPC), and flight warning computer (FWC), and activation of the stop
rudder input aural warning (SRIW) device, as specified in a European
Union Aviation Safety Agency (EASA) AD, which will be incorporated by
reference. The FAA is proposing this AD to address the unsafe condition
on these products.
DATES: The FAA must receive comments on this proposed AD by July 6,
2020.
ADDRESSES: You may send comments, using the procedures found in 14 CFR
11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue SE, Washington, DC 20590.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For the material identified in this proposed AD that will be
incorporated by reference (IBR), contact the EASA, Konrad-Adenauer-Ufer
3, 50668 Cologne, Germany; telephone +49 221 89990 1000; email
[email protected]; internet www.easa.europa.eu. You may find this IBR
material on the EASA website at https://ad.easa.europa.eu. You may view
this IBR material at the FAA, Airworthiness Products Section,
Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For
information on the availability of this material at the FAA, call 206-
231-3195. It is also available in the AD docket on the internet at
https://www.regulations.gov by searching for and locating Docket No.
FAA-2020-0456.
Examining the AD Docket
You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-
0456; or in person at Docket Operations between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays. The AD docket contains
this NPRM, any comments received, and other information. The street
address for Docket Operations is listed above. Comments will be
available in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Vladimir Ulyanov, Aerospace Engineer,
Large Aircraft Section, International Validation Branch, FAA, 2200
South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3229;
email [email protected].
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written relevant data, views, or
arguments about this proposal. Send your comments to an address listed
under the ADDRESSES section. Include ``Docket No. FAA-2020-0456;
Product Identifier 2020-NM-053-AD'' at the beginning of your comments.
The FAA specifically invites comments on the overall regulatory,
economic, environmental, and energy aspects of this NPRM. The FAA will
consider all comments received by the closing date and may amend this
NPRM based on those comments.
The FAA will post all comments the FAA receives, without change, to
https://www.regulations.gov, including any personal information you
provide. The FAA will also post a report summarizing each substantive
verbal contact the FAA receives about this NPRM.
Discussion
The EASA, which is the Technical Agent for the Member States of the
European Union, has issued EASA AD 2020-0077, dated March 31, 2020
(``EASA AD 2020-0077'') (also referred to as the Mandatory Continuing
Airworthiness Information, or ``the MCAI''), to correct an unsafe
condition for certain Airbus SAS Model A330-202, -203, -223, -243, -
301, -321, -322, -323, -341, -342, and -343 airplanes; and Model A340-
211, -212, -213, -311, -312, and -313 airplanes.
This proposed AD was prompted by a report indicating that the
allowable load limits on the vertical tail plane could be reached and
possibly exceeded in cases of multiple rudder doublet inputs. The FAA
is proposing this AD to address cases of multiple rudder doublet
inputs, which could lead to excessive loads on the vertical tail plane
and a subsequent loss of control of the airplane. See the MCAI for
additional background information.
Related IBR Material Under 1 CFR Part 51
EASA AD 2020-0077 describes procedures for upgrading the FCDC,
associated FCPC, and FWC, and activation of the SRIW device. This
material is reasonably available because the interested parties have
access to it through their normal course of business or by the means
identified in the ADDRESSES section.
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to the FAA's bilateral agreement with the State of Design Authority,
the FAA has been notified of the unsafe condition described in the MCAI
referenced above. The FAA is proposing this AD because the FAA
evaluated all the relevant information and determined the unsafe
condition described previously is likely to exist or develop in other
products of the same type design.
Proposed AD Requirements
This proposed AD would require accomplishing the actions specified
in EASA AD 2020-0077 described previously, as incorporated by
reference, except for any differences identified as exceptions in the
regulatory text of this AD.
Explanation of Required Compliance Information
In the FAA's ongoing efforts to improve the efficiency of the AD
process, the FAA initially worked with Airbus and EASA to develop a
process to use certain EASA ADs as the primary source of information
for compliance with requirements for corresponding FAA ADs. The FAA has
since coordinated with other manufacturers
[[Page 31084]]
and civil aviation authorities (CAAs) to use this process. As a result,
EASA AD 2020-0077 will be incorporated by reference in the FAA final
rule. This proposed AD would, therefore, require compliance with EASA
AD 2020-0077 in its entirety, through that incorporation, except for
any differences identified as exceptions in the regulatory text of this
proposed AD. Using common terms that are the same as the heading of a
particular section in the EASA AD does not mean that operators need
comply only with that section. For example, where the AD requirement
refers to ``all required actions and compliance times,'' compliance
with this AD requirement is not limited to the section titled
``Required Action(s) and Compliance Time(s)'' in the EASA AD. Service
information specified in EASA AD 2020-0077 that is required for
compliance with EASA AD 2020-0077 will be available on the internet at
https://www.regulations.gov by searching for and locating Docket No.
FAA-2020-0456 after the FAA final rule is published.
Costs of Compliance
The FAA estimates that this proposed AD affects 10 airplanes of
U.S. registry. The FAA estimates the following costs to comply with
this proposed AD:
Estimated Costs for Required Actions
----------------------------------------------------------------------------------------------------------------
Labor cost Parts cost Cost per product Cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
Up to 10 work-hours x $85 per hour Up to $31,038......... Up to $31,888......... Up to $318,880.
= $850.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII: Aviation Programs,
describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701: ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
The FAA determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
Airbus SAS: Docket No. FAA-2020-0456; Product Identifier 2020-NM-
053-AD.
(a) Comments Due Date
The FAA must receive comments by July 6, 2020.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Airbus SAS airplanes identified in paragraphs
(c)(1) through (4) of this AD, certificated in any category, as
identified in European Union Aviation Safety Agency (EASA) AD 2020-
0077, dated March 31, 2020 (``EASA AD 2020-0077'').
(1) Model A330-202, -203, -223, and -243 airplanes.
(2) Model A330-301, -321, -322, -323, -341, -342, and -343
airplanes.
(3) Model A340-211, -212, and -213 airplanes.
(4) Model A340-311, -312, and -313 airplanes.
(d) Subject
Air Transport Association (ATA) of America Code 27, Flight
Controls.
(e) Reason
This AD was prompted by a report indicating that the allowable
load limits on the vertical tail plane could be reached and possibly
exceeded in cases of multiple rudder doublet inputs. The FAA is
issuing this AD to address cases of multiple rudder doublet inputs,
which could lead to excessive loads on the vertical tail plane and a
subsequent loss of control of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified,
unless already done.
(g) Requirements
Except as specified in paragraph (h) of this AD: Comply with all
required actions and compliance times specified in, and in
accordance with, EASA AD 2020-0077.
(h) Exceptions to EASA AD 2020-0077
(1) Where EASA AD 2020-0077 refers to its effective date, this
AD requires using the effective date of this AD.
(2) The ``Remarks'' section of EASA AD 2020-0077 does not apply
to this AD.
(i) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
Large Aircraft Section, International Validation Branch, FAA, has
the authority to approve AMOCs for this AD, if requested using the
procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19,
send your request to your principal inspector or local Flight
Standards District Office, as appropriate. If sending information
directly to the Large Aircraft Section, International Validation
Branch, send it to the attention of the person identified in
paragraph (j)(2) of this AD. Information may be emailed to: [email protected]. Before using any approved AMOC, notify
your appropriate principal inspector, or lacking a principal
inspector, the manager of the local flight standards district
office/certificate holding district office.
(2) Contacting the Manufacturer: For any requirement in this AD
to obtain instructions
[[Page 31085]]
from a manufacturer, the instructions must be accomplished using a
method approved by the Manager, Large Aircraft Section,
International Validation Branch, FAA; or EASA; or Airbus SAS's EASA
Design Organization Approval (DOA). If approved by the DOA, the
approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): For any service information
referenced in EASA AD 2020-0077 that contains RC procedures and
tests: Except as required by paragraph (i)(2) of this AD, RC
procedures and tests must be done to comply with this AD; any
procedures or tests that are not identified as RC are recommended.
Those procedures and tests that are not identified as RC may be
deviated from using accepted methods in accordance with the
operator's maintenance or inspection program without obtaining
approval of an AMOC, provided the procedures and tests identified as
RC can be done and the airplane can be put back in an airworthy
condition. Any substitutions or changes to procedures or tests
identified as RC require approval of an AMOC.
(j) Related Information
(1) For information about EASA AD 2020-0077, contact the EASA,
Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221
89990 6017; email [email protected]; Internet www.easa.europa.eu.
You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. You may view this material at the FAA,
Airworthiness Products Section, Operational Safety Branch, 2200
South 216th St., Des Moines, WA. For information on the availability
of this material at the FAA, call 206-231-3195. This material may be
found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-
2020-0456.
(2) For more information about this AD, contact Vladimir
Ulyanov, Aerospace Engineer, Large Aircraft Section, International
Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198;
telephone and fax 206-231-3229; email [email protected].
Issued on May 15, 2020.
Lance T. Gant,
Director, Compliance & Airworthiness Division, Aircraft Certification
Service.
[FR Doc. 2020-10978 Filed 5-21-20; 8:45 am]
BILLING CODE 4910-13-P